Central Vacuum Repair guide do it yourself
Central Vacuum Repair Guiide and Tips :
Central Vacuum How to fix it yourself tips and process.
Most of our customers are successful in troubleshooting and repairing their central vacuum system themselves. Follow our quick links below and you can be troubleshooting your central vacuum system in minutes. Use our easy to follow steps, written by the experts at Central Vacuum Stores, to locate and diagnose central vacuum problems.
Symptom NO SUCTION or REDUCED SUCTION / AIRFLOW
Quick, possible solutions ro reduced central vacuum suction
- Canister or filter bag might be full.
Empty canister or replace filter bag.
Filter bag might be damaged (torn, hole etc).
Replace or repair filter bag.
Secondary filter might be dirty.
Clean or replace secondary filter.
Exhaust vent system might be blocked or clogged.
Dirt canister might not be installed properly
Fasten or repair latches to dirt canister
Symptom CLOG IN THE HOSE
- Take your central vacuum hose and connect it directly to the dirt canister.
- After turning on the vacuum, if the hose has normal suction then the clog exists in your tubing.
- Then check all the tube for clog.
- But, if you experience reduced suction at the canister then your hose is clogged.
- Plug hose in reverse into the inlet located on your unit and turn on the system. This should aspirate the clog out.
- Or, remove the hose from the inlet and push a garden hose through hose to push out the clog. Most importantly, the garden hose must be turned off and there should be absolutely no water entering your vacuum hose.
- Or, remove the hose from inlet and drop in a heavy object such as a screwdriver to push out clog.
If you are still unsuccessful in clearing out the hose clog, call us at 703 997 9292 for solution.
Sypmtom PARTIAL CLOG IN CENTRAL VACUUM PIPE
How to determine a partial clog in tubing
- Turn on unit at the canister and insert a TornadoPower® Cloth through each inlet. If the cloth gets to the canister in one piece you do not have a blockage in that inlet, move on to the next inlet and test again.
- If the cloth gets to the canister but is torn or ripped you probably have a partial clog or blockage.
- Even if you find a clog in one of the inlets, test all the inlets one at a time to make sure you don’t have more than one clog.
- Plug hose into each inlet and place hand over hose end in order to build up air pressure and then release. Try this a couple of times in each inlet.
If you are still unsuccessful in clearing out the partial tubing clog, please call us at 703 997 9292 for solution.
Symptom FULL CLOG IN CENTRAL VACUUM PIPE
How to determine a full clog in tubing
- Turn on unit at the canister and insert a TornadoPower® Cloth through each inlet. If the cloth gets to the canister in one piece you do not have a blockage in that inlet, move on to the next inlet and test again. If the cloth does not make it back to the canister then you have a clog/obstruction in your tubing.
- After you find which inlet run is affected, turn off your central vacuum system and then remove the canister from the system. Then by using a separate vacuum (such as portable wet/dry canister) plug in the hose into the inlet and try to aspirate the clog out. This method works most of the time.
- If the above did not work, you can try using a plumber’s snake through the inlet to push the clog out.
If you are still unsuccessful in clearing out the tubing clog, please call us at 703 997 9292 for solution.
Symptom LEAK IN SYSTEM
Quick, possible solutions to a leak in your central vacuum system
Multiple hoses are plugged in at once.
Unplug additional hoses.
Inlet covers removed or broken.
Reinstall or repair inlet covers.
- On systems with toe kick cleaning devices, the door is stuck in the open position.
Multiple hoses are plugged in at once.
Unplug additional hoses.
Damage to tubing, disconnected or broken.
Repair or replace damaged tubing.
UNIT RUNS CONTINUOUSLY (won’t shut off)
Follow these steps to determine the cause of this central vacuum issue
- If your unit has an on/off switch make sure that it is in the off position. Disconnect one of the low voltage wires from the unit body.
- If the unit continues to run, you have a bad relay and it must be replaced.
- Call us at 703 997 9292 to determine which relay you need
- If the unit turns off but turns on again when you reconnect the wire, you have a short in the system wire.
Investigating a short in the system wire
- The short may be occurring in one of the inlets. While the unit is running, check each inlet by un-screwing the faceplate from the mounting bracket. If the unit stops after backing out the screws that secure the low voltage wires then remove that valve, reverse the wire, and carefully screw the faceplate back to the mounting bracket.
- If you’ve checked all inlets and this does not solve the issue, check the wire in any accessible space where the pipe and wire may be reached such as a crawl space, attic or basement. You may find that if you had any recent service work done on your house that it may have caused the short.
- Another possible cause may be rodents chewing through the wire and causing the short. If you locate this, repair wire.
- If are still unable to fix this issue, you can purchase an RFX Remote Controller. This product will allow you to turn your system on and off with a key fob type device from any part of your home.
If you need tech support, please call us at 703 997 9292 for solution.
POWER UNIT WILL NOT TURN ON
Follow these steps to determine why your central vacuum will not turn on
- Check the house circuit breaker to see if it tripped.
- If it is tripped, then turn off your central vacuum unit and reset the circuit breaker. Then turn the central vacuum unit on.
- If the circuit breaker trips again, determine if the house circuit your vacuum unit is on has sufficient voltage required.
- If your unit has a reset button, press the button and try again.
- Cross the low voltage wire from the relay at the unit with aTo determine the relay replacement that you need please give us a call at 703 997 9292 for solutions.
DAMAGE TO CENTRAL VACUUM PIPE (such as punctures or cracks)
How to replace damaged tubing in your central vacuum system
- Cut a new piece of pipe to replace damaged portion of pipe.
- Apply PVC glue to the exterior of the existing tubing. (Do not apply glue to the interior of the coupler.)
- Install coupler to the piece of pipe that had glue applied. Twist coupler for stronger bond.
- Apply PVC glue to the exterior of the new piece of tubing to be installed.
- Install new piece of pie to coupler. Twist pipe for stronger bond.
- Complete installation by connecting new piece of pipe to the other side by repeating steps 2-5.
CLEANING YOUR CENTRAL VACUUM PIPE
TORNADOPOWER® Central Vacuum Maintenance Cloths are the do-it-yourself solution for central vacuum system care. These handy cloths are the ultimate way to reduce odors and restore your system to peak efficiency.
Turn on unit at the canister and insert a TornadoPower® cloth through each inlet and through your hose. The textured cloths are specially formulated to capture dirt and grime residue that exists in the hose and tubing. Also, when pulled through the pipe system, these cloths capture larger debris such as pebbles, lint, sticks, etc. and deliver these items to the canister. Finally, the treated cloths “wipe down” the inside walls of hoses and tubing, and their scented solution leaves the entire system smelling clean and fresh.
- 22 Mar, 2022