Common repair problem in Bissell vacuum cleaner | Sameday vacuum repair

What are the common repair problems in a Bissell vacuum cleaner?
Customers say my,
Bissell has low suction,
Bissell Roller brush is not spinning
Bissell has no power
Bissell Filter is clogged
Bissell has burning smell
Bissell Hose is clogged
Bissell has loud noise
Bissell motor repair.

How to repair Bissell Roller brush not spinning issues?
Bissell PowerForce® Helix® Upright Vacuum Model #'s 1700, 1701, 1797, 2190, 2191, 21913, 2691, 2692 PowerForce Helix/Turbo/Rewind PowerForce® Helix® (Rewind / Non-Rewind) Upright Vacuum Model #'s 3313, 3313U, 3332, 3333.

Flatten the Bissell handle Unscrew 5 Phillips head screws to remove Brush Access Plate

Hold Bissell Brush roll on both ends and lift Brush out

Remove screw securing the Lower Hose

Push a broomstick through Bissell Hose toward Brush area to clear Lower Hose & Brush area of all debris

Inspect Lower Hose, Belt and Brush roll Access Plate for damage
If Bissell Brush does not spin freely > Replace Bissell Brush
Reattach Bissell Belt by looping it onto motor shaft, then around Brush

Stretch Bissell Belt until the Brush is secure
Rotate Brush roll several times to align Belt correctly
Reinstall Brush roll Access Plate and screws
Reattach Lower Hose, secure the screw

How to repair Bissell power issues?
Bissell PowerForce® Helix® Upright Vacuum Model #'s 1700, 1701, 1797, 2190, 2191, 21913, 2691, 2692 PowerForce Helix/Turbo/Rewind PowerForce® Helix® (Rewind / Non-Rewind) Upright Vacuum Model #'s 3313, 3313U, 3332, 3333

Unplug Bissell vacuum
Run hand along entire length of power cord, it should be smooth
Check plug for damage
Is either the cord or plug (prongs) damaged or the motor.
Bring it to your nearest acevacuums in virginia for vacuum service.

How to replace the filters in the Bissell vacuum cleaner?
Bissell PowerForce® Helix® Upright Vacuum | Cleaning Filters Model #'s 1700, 1701, 1797, 2190, 2191, 21913, 2691, 2692 PowerForce Helix/Turbo/Rewind PowerForce® Helix® (Rewind / Non-Rewind) Upright Vacuum Model #'s 3313, 3313U, 3332, 3333.
Cleaning Bissell tank & Bissell filters are considered a part of routine maintenance Remove & empty dirt tank.

Release the Bissell Separator by twisting to the left to disconnect & remove
Clean Separator of all debris
Bissell Separator can be rinsed > Allow to completely air dry 24 hours before reinstalling
Clean Bissell filter Open the tank lid > Lift release latch on front of tank Remove filter Wash filter with warm water > Allow 24 hours to dry

Reinstall parts
Reattach separator into dirt tank by twisting left
Reinstall filter
Attach Bissell dirt tank back onto machine

How to repair bissell low or no suction issues?

PowerForce® Helix® Upright Vacuum

Model #'s 1700, 1701, 1797, 2190, 2191, 21913, 2691, 2692 PowerForce Helix/Turbo/Rewind PowerForce® Helix® (Rewind / Non-Rewind) Upright Vacuum Model #'s 3313, 3313U, 3332, 3333
If your Bissell vacuum is not suctioning like it used to it is likely due to an obstruction in the air pathway.

Follow these steps to resolve:

Test for suction at end of the Hose (dirt tank must be attached to machine)
Lift the Hose from the base
Turn on, hold hand over end of end of Hose